
BIQU B1 Dual Operation System 3D Printer
BIQU B1 with High Quality 32 Bit Duel Opration System ; Supports 15 languages ; BIGTREETECH SKR V1.4 32-Bit motherboard; Dual operation system(Marlin&touch work modes) ; TMC silent drive;New integrated adapter board; TypeC Connect
ExplorePICKED FOR YOU
BIGTREETECH SKR E3 Turbo
Introduction:
1.Adopts ARM Cortex-M3 series LPC1769 chip, the main frequency is up to 120MHz
2.5 TMC2209 drivers on board, supporting dual extruders
3.Add parallel double Z-axis interface
4.Support BLtouch, filament detection, power-off resume, automatic shutdown, etc
5.Support onboard Sensorless homing function
...
BIGTREETECH SKR MINI E3 V2.0
- 1.Use MP1584EN power chip, support 12-24V power input, the maximum output current can reach 2.5A.
- 2. The hot-bed MOS tube uses WSK220N04, low on-resistance, larger heat dissipation area and reduces heat generation.
- 3.double Z-axis .
- 4. Supports BLtouch, detection of blocked rotation, resumption of shutdown, shutdown after shutdown, etc.
- ....
BIGTREETECH SKR V1.4 & SKR V1.4 Turbo
BIGTREETECH TFT43&TFT50&TFT70 V3.0
2.Serial screen mode supports two printing methods: SD card and U disk.
3.Reserve WIFI interface, support external WIFI module to realize WIFI function.
4. sets of UART serial expansion ports are reserved for user DIY
5.support up to 15 languages
BIQU H2 Direct Extruder
- Weight
- 211g (including heating aluminum block, fan)
- Extrusion method
- Double gear extrusion
- Maximum extrusion force
- 7.5kg (depending on filaments)
- Motor recommended current
- 800mA
- Maximum printing temperature
- 260℃ (upgradeable to 500℃)
- Extrusion capacity (based on existing)
- 600mm³/min(depending on filaments)
- Number of pulses
- Step motor drive at 932steps/mm at 16 segments (further correction required)

BIQU eSUN PLA+ 3D Printer Filament
- Printing temperature
- 210-230 ℃
- Base plate temperature
- 45-60 ℃
- Density
- 1.23 g/cm³
- Printing speed
- 40-100 mm/s
- Fan
- 100 %
- Melt Index
- 5(190 ℃/2.16 kg) g/10min
- Tensile Strength
- 63 Mpa
- Elongation at break
- 20 %
- Bending strength
- 74 Mpa
- Flexural modulus
- 1973 Mpa

BIGTREETECH Control Board
-
Type1:Only SKR V1.4 Board
-
Type2:Only SKR V1.4 Turbo Board
-
Type3:SKR V1.4 +TMC2208 V3.0
-
Type4:SKR V1.4 +TMC2209 V1.2
- + 7
-
Only the board
-
With 5*PCS TMC2208
-
With 5pcs TMC2208 UART
-
With 5*pcs TMC2209
- + 2
BIGTREETECH Screen&LCD
-
type1:Clone prusa buddy+mini LCD28 v1.0
-
type2::Clone prusa buddy
-
type3:mini LCD28 v1.0
BIGTREETECH Driver Board
-
Type1:Only SKR V1.4 Board
-
Type2:Only SKR V1.4 Turbo Board
-
Type3:SKR V1.4 +TMC2208 V3.0
-
Type4:SKR V1.4 +TMC2209 V1.2
- + 7
-
type1:Clone prusa buddy+mini LCD28 v1.0
-
type2::Clone prusa buddy
-
type3:mini LCD28 v1.0
BIGTREETECH Module&Expansion Board
BIQU Extruder&Hotend
-
Blue High flow
-
Blue Standard Flow
-
Black High flow
-
Black Standard Flow
-
1.75/0.4MM
-
1.75/0.6MM
-
1.75/0.8MM
-
1.75/1.0MM
- + 1
BIQU Printing Plateform&HeatBed
Hot Deals
-
Blue High flow
-
Blue Standard Flow
-
Black High flow
-
Black Standard Flow